- WWW.ORAGIE.COM - ОРЪЖЕЕН И ИНТЕРНЕТ ОРЪЖЕЕН МАГАЗИН - Форуми - WWW.ORAGIE.COM - ОРЪЖЕЕН И ИНТЕРНЕТ ОРЪЖЕЕН МАГАЗИН -
УЛ. ИВАН ДЕНКОГЛУ № 7, СОФИЯ 1000 - ТЕЛЕФОН ЗА ПОРЪЧКА: 0899-15-18-15 - ОРЪЖИЕ - AIRSOFT - ЛОВ - ЛОВЕН ТУРИЗЪМ
 
 Въпроси/ОтговориВъпроси/Отговори   ТърсенеТърсене   ПотребителиПотребители   Потребителски групиПотребителски групи   Регистрирайте сеРегистрирайте се 
 ПрофилПрофил   Влезте, за да видите съобщенията сиВлезте, за да видите съобщенията си   ВходВход 

WF-WB800 Harden Flanged Bearing Plastic Bearing Manufacturer

 
Създайте нова тема   Напишете отговор    - WWW.ORAGIE.COM - ОРЪЖЕЕН И ИНТЕРНЕТ ОРЪЖЕЕН МАГАЗИН - Форуми -> ОРЪЖЕЕН МАГАЗИН
Предишната тема :: Следващата тема  
Автор Съобщение
bearingtypes
Новак
Новак


Регистриран на: 01 Юни 2017
Мнения: 11

МнениеПуснато на: Пет 12 Яну, 2018 6:03 am    Заглавие: WF-WB800 Harden Flanged Bearing Plastic Bearing Manufacturer Отговорете с цитат

Simple Treatment of Textile Sealed Bearings
New cotton spinning equipment due to dust, heat and high-speed requirements, the use of a large number of SOLP guide slide plate, wear pad, oilless bearing plate. These bearings run a certain period of time, due to internal copper sleeve for lack of oil, resulting in dry and damaged bearings. Such as the import of air spinning machine sealed bearings, the number of good, but the use of a few years later, because they can not be cleaned and replenished grease, so that a large number of sealed bearings damaged scrapped, an increase of equipment failure and unnecessary expenses.

Two simple and effective cleaning and refueling methods are described. The first set of bearing manufacturer cylinder cleaning method, apply to the WF-WB800 Harden Flanged Bearing shell at both ends of the sealed bearings. The method is first soaked in kerosene bearing 1h a 2h, and then according to the bearing diameter size, make special sleeve, both cleaning, but also fuel. Sleeve diameter slightly larger than the bearing diameter 0.05 mm ~ 0.08 mm, slightly lighter than the bearing. Cleaning and refueling steps: the amount of kerosene into the sleeve, the bearing hand pressed into the use of the gap itself bearing, kerosene will be squeezed out, repeated 1 to 2 times; clean and dry and then add the necessary sleeve grease , The bearing into the sleeve with a dry bearing pressure device gently under pressure, the number of bearing refueling according to the needs of flexible control. The second applies to special fully enclosed bearings with a clearance at one end and a setscrew hole. Using the positioning screw hole and the bearing clearance, the first bearing soaked in kerosene in 1 h ~ 2 h, with a special nozzle and oil gun inhaled kerosene, repeated into the bearing 2 or 3 times, dripping with oil gun after the required lubrication Grease can be added.

The above approach applies to a variety of imported or domestic sealed bearings and special sealed bearings, these plastic bearings can be cleaned if the regular fuel, will be able to extend its service life, and can save a lot of money and reduce the occurrence of bad vehicles.
Върнете се в началото
Вижте профила на потребителя Изпратете лично съобщение
Покажи мнения от преди:   
Създайте нова тема   Напишете отговор    - WWW.ORAGIE.COM - ОРЪЖЕЕН И ИНТЕРНЕТ ОРЪЖЕЕН МАГАЗИН - Форуми -> ОРЪЖЕЕН МАГАЗИН Часовете са според зоната GMT + 2 Часа
Страница 1 от 1

 
Идете на:  
Не Можете да пускате нови теми
Не Можете да отговаряте на темите
Не Можете да променяте съобщенията си
Не Можете да изтривате съобщенията си
Не Можете да гласувате в анкети


Powered by phpBB © 2001, 2005 phpBB Group
Translation by: Boby Dimitrov